Most sealers sit on your pavers. ULTRA SEAL cures into them — a two-part, commercial-grade urethane that deepens color, lays down a classic gloss, and locks joint sand in place. Clean, sand, and seal in one day — even on damp pavers.
Typical one-part acrylics look great for a season. Then sun, sprinklers, and hot tires go to work — and by next spring you're stripping and starting over.
Moisture gets trapped under the film and blushes cloudy white — the classic milky driveway. The finish is ruined, and stripping it is a weekend you'll never get back.
Thin films sit on top of the paver instead of bonding into it. UV and hot tire pressure lift the edges, and it sheds like old paint.
Unlocked sand rinses away with every storm. Then come the weeds, the ants, and the wobbly pavers underfoot.
Ultra Seal was engineered against all three — a two-part chemistry that bonds, locks, and outlasts.
One-part sealers dry. Ultra Seal reacts. When Part A meets Part B, the urethane cross-links into a single continuous shield — bonded to the paver, not resting on it.
Water-based carrier with a 48% solids payload — the gloss, the color depth, the body.
The catalyst. It starts the cross-linking reaction the moment the two meet.
Abrasion-resistant. Chemical-resistant. Hot-tire resistant. Locked to the surface and to the sand between every joint — for years, not seasons.
Apply right after the pressure wash. No "come back in 48 hours" — the water-based chemistry is built for damp pavers.
A high-solids concentrate you dilute on site — one 5-gallon kit runs a flood coat and a finish coat across 1,000–1,500 sq ft.
Locks joints up to 3/8-inch wide and eliminates the need for polymeric sand — while shutting down weeds and insect nests.
Same pavers, one pass of Ultra Seal apart — dusty and washed-out on one side, deep color under classic gloss on the other.
Because Ultra Seal applies to damp pavers, the whole job fits in a single Saturday. Here's the play:
Blast off dirt, mold, and any failing old sealer. No drying-out period needed afterward.
Plain joint sand is fine — the sealer does the locking, so skip the pricey polymeric.
Pour Part B into Part A (4:1) and paddle-mix for two minutes. The reaction is on.
Diluted 1:4 with water, it soaks deep — saturating the sand and stabilizing every joint.
Once the flood coat turns clear and tacky, lay down the 1:1 finish coat for depth and gloss.
Touch-dry in 1–2 hours. Keep traffic off overnight — walk it in 24.
// SAMPLE SCHEDULE — ACTUAL TIMING VARIES WITH WEATHER, SURFACE & AREA
Stabilizes joints up to 3/8-inch wide and eliminates the need for polymeric sand. What you sweep in, stays in.
Cross-linked urethane shrugs off hot tire marks — the number one killer of driveway sealers.
UV protection keeps the gloss glossy and the color deep — season after season in hard sun.
Sealed joints and a chemical-resistant surface inhibit mold, algae, weed growth, and insect nests.
Water-based, biodegradable, minimal odor, and VOC-compliant in all 50 states. It won't harm your vegetation.
No 48-hour dry-out. Wash it, sand it, seal it — one mobilization, one Saturday, done.
| Ultra Seal 2-Part Urethane | Typical 1-Part Acrylic | |
|---|---|---|
| Chemistry | ✦Cross-linked, bonded shield | Thin film sitting on the surface |
| Solids | ✦48% solids concentrate | Often 15–30% |
| Joint sand | ✦Locks up to 3/8″ joints | Limited to no stabilization |
| Hot tires | ✦Resistant | Prone to marking and lift |
| Application | ✦Damp or dry — one-day job | Usually needs a bone-dry surface |
| Recoat cycle | ✦Years, not seasons | Often every 1–2 years |
"Typical 1-part acrylic" reflects common characteristics of entry-level acrylic sealers; always compare against your product's technical data sheet.
Measure your patio, pool deck, or driveway — length × width — and let the calculator size your order. Coverage runs 200–300 sq ft per gallon depending on how porous your pavers are and how wide the joints run.
Estimate only — porous pavers and wide joints drink more. One 5-gal kit seals 1,000–1,500 sq ft. Unsure? Call 813-308-9202 and talk it through.
Yes — that's the headline feature. Ultra Seal is formulated to apply over damp pavers, so there's no multi-day drying window between cleaning and sealing. Wash in the morning, seal in the afternoon.
It's the deep, just-rained wet look with a classic gloss finish — the one that makes the color of the paver pop. If you're after a different sheen for your project, call the shop at 813-308-9202 and they'll point you to the right formula.
Pour 1 gallon of Part B into 4 gallons of Part A and paddle-mix for two full minutes. Once combined, the cure clock starts — so mix when you're ready to apply, and mix only what the day's job needs.
Ultra Seal is water-based, biodegradable, low odor, and VOC-compliant in all 50 states — it won't harm surrounding vegetation. Keep pets and people off the surface until it's dry to the touch (1–2 hours) and give it 24 hours before regular foot traffic.
Coverage runs 200–300 sq ft per gallon depending on paver porosity and joint width, and one 5-gallon kit typically handles 1,000–1,500 sq ft with the flood-plus-finish system. Use the coverage calculator above for a quick order size.
Shipping is free on all orders to the lower 48 — no minimum, for a limited time. Product is warranted as material-only if proven defective. Questions before or during your job? Real humans answer at 813-308-9202 or info@paversealerstore.com.
The 5-gallon Ultra Seal pro kit is $321 with free shipping — enough to give 1,000–1,500 sq ft the wet look that lasts years, not seasons.